Disclaimer
This guide is intended for installers with a working knowledge of automotive electrical systems. While the Altricity Jump Starter is engineered for safety and reliability, the manufacturer assumes no liability for damage, loss, or injury resulting from improper installation or misinterpretation of these instructions.
By proceeding with the installation, you, the installer, assume all responsibility for the correct and safe application of this product.
- Always verify vehicle compatibility and follow all safety precautions.
- Never modify the product or its internal wiring.
- If you are uncertain about any step, stop and consult Altricity Support.
Introduction
A Note to Our Professional Partners,
Thank you for choosing Altricity. We designed the Altricity Jump Starter not just to be the most reliable smart jump starter on the market, but to make your installation process as quick and seamless as possible. This guide will walk you through a successful installation, ensuring happy customers and zero comebacks.
Key Features
- One Size – Fits Many: The Altricity Jump Starter is designed to fit most modern cars using 12V systems.
- Built for the Engine Bay: The IP67-rated, sealed enclosure resists dust, water, and oil, ensuring long-term durability and preventing service calls.
- Reliable Power: Starts engines of all kinds. From 4-cylinder cars to 8-cylinder trucks, in any weather.
- Simple Diagnostics: Integrated Bluetooth and the Altricity mobile app enables immediate verification of post-installation.
What's in the Box
- 1x Altricity Jump Starter Unit (with 18-inch 10 AWG Cables)
- 1x QR Code Card for App Download
Install the Altricity Remote Jump Starter App from the App Store (iOS) or Play Store (Android) to use the device.
Pre-Installation Check
Safety and Preparation
- Confirm that the vehicle operates on a 12V electrical system.
- Disconnect the vehicle battery before wiring.
- Avoid wearing metallic jewelry while working near battery terminals.
Table 1: Tools and Equipment required
| Item | Quantity | Description |
|---|---|---|
| Wrench | 1 | For battery terminal connections |
| Industrial Mounting Tape or Reclosable Fastener | As required | For secure mounting. Use 3M SJ3550/SJ3560 or similar. |
| 8 AWG Wire | 24-48" | For extending the cable in cases where Altricity device must be mounted farther from vehicle battery. |
| Soldering Iron (Optional) | 1 | For Joining wires in case of extension |
| Heat Shrink Tubing (Optional) | As required | For insulation |
| Wire Stripper | 1 | For cable preparation |
The Installation
Step 1: Mount the Altricity Jump Starter
Installation in the Engine Bay:
For maximum performance and reliability, the Altricity Jump Starter is designed to be installed in the vehicle's engine bay within reach of the battery using the supplied 10 AWG cables.
Choose a flat, clean surface. This could be next to the car's battery, fuse box or a suitable location in the engine bay away from direct heat and moving parts (belts, fans). Place and mount the unit at the location you have determined securely using adhesive tape, fasteners, or brackets as appropriate.
1: Altricity Jump Starter Unit installed on the side of a vehicle battery
Installation in other locations
If no suitable location is available in the engine bay:
- Select an alternate location agreed upon with the vehicle owner (e.g., glove box, under seats, or trunk).
- Measure the total cable length required to reach the battery.
- Upgrade the power cable to the correct gauge per the Wire Sizing Guide on page 16.
- Cut the supplied 10 AWG wire down to roughly 2 inches and solder and heat-shrink the additional length of 8 AWG wire to the Altricity Jump Starter unit.
- Route the cables securely to the battery compartment.
- Terminate with appropriate ring connectors and secure to the battery posts.
2: Example of an Altricity Jump Starter installed in on top of a fuse box.
Some models, German SUV models for example, have batteries located in alternate locations like the floorboard behind the front seats or in the interior of the rear quarter panel. These areas may allow for placement of the unit adjacent to the battery.
3: Altricity Jump Starter installed in the rear quarter panel
Step 2: Connect Altricity Jump Starter to the Vehicle Battery
Connect the positive lead (RED) from the Altricity Jump starter to the positive battery terminal.
Connect the negative lead (BLACK) of the Altricity Jump Starter to the negative battery terminal of the vehicle battery.
Ensure that all connections are secure.
4: Connections from Altricity Jump Starter to the vehicle battery
Step 3: Cable Management
Tidy up the cables using zip ties to secure them. Make sure the cables are not in contact with sharp edges, hot surfaces, or moving parts.
Step 4: Powering-up and Pairing
Find the power button on the Altricity Jump Starter and push it to turn the unit on.
Install the Altricity App on the customers phone from the corresponding app store (Play Store for Android and App Store for Apple). Scan the QR Code below to quickly reach download the app.
5: QR Code to download Altricity App
Once installed, open the Altricity App and sign up using your preferred method.
Fill in the details of the car such as make, model and year. Once all the details are filled in, the app will take you to the scan and connect page.
Use the Scan and Connect feature in the app to locate and pair with the Altricity Jump Starter. Follow the instructions on the screen to complete the pairing process.
Once connected and paired, verify the connection and installation by checking:
- Jump Starter Battery Level
- Vehicle Battery voltage
- Systems Information within the app.
Note: Make sure to press the PAIR Button on the Altricity Unit before attempting to pair a new mobile phone. The Altricity Jump Starter is designed to work with one phone only. Pairing a new mobile phone may prevent the unit from connecting to the previous mobile phone.
Step 5: Finishing Touches
Verify that the car battery voltage is displayed correctly in the app.
Additionally, we recommend checking and applying any available firmware updates to keep your Altricity Jump Starter up to date.
We recommend that you check if the clearance between the hood and unit is enough before shutting the hood hard enough to latch, which could cause damage to both the unit and the hood.
Troubleshooting
Table 2: Troubleshooting steps
| No. | Problem | Troubleshooting Step |
|---|---|---|
| 1 | Unit does not power on. | Verify red wire is on the Positive (+) terminal and Black is on the Negative (-). Ensure the power switch on the Unit is in the ON Position. |
| 2 | App Cannot Find Altricity Jump Starter Unit | Ensure unit power is ON. Stay within 20 feet range. Confirm Bluetooth is enabled, and correct user account is signed in. If pairing fails, press and hold the PAIR button and retry. |
Wire Sizing Guide
The wire sizing guide ensures that the power cables used between the Altricity Jump Starter and the vehicle battery are appropriately rated for the installation length. Selecting the correct wire gauge minimizes voltage drop, prevents overheating, and guarantees reliable current delivery during engine cranking. Always refer to this table when extending or replacing the supplied power cables.
Table 3: Wire Sizing Guide for extensions
| Total Length of Cable | Suggested Guage for Cable |
|---|---|
| 18-24 inches | 10 AWG |
| 24-48 inches | 8 AWG |
Revision History
| Revision | Date | Remarks |
|---|---|---|
| 1 | October 13, 2025 | First version |
Page 1 of 16 | Altricity LLC | All Rights Reserved
